Frequently Asked Questions

Here is a list of questions most commonly asked about WOHOBOs and garden studios in general. If you can’t find what you’re looking for, then please contact us directly and we’d be really happy to help.

We offer six standard studio sizes. Dimensions below include external size, internal usable space, and the front porch.

All studios share the same height:

External height:
2430mm (highest point – rear)
2330mm (lowest point – front)

Internal ceiling height:
2180mm (highest point – rear)
2080mm (lowest point – front)

StudioExternal (mm)Internal (mm)Internal areaPorch
Studio022175 x 21552015 x 16853.4m²300mm
Studio02 More2175 x 31552015 x 26855.4m²300mm
Studio033175 x 21553015 x 16855.1m²300mm
Studio03 More3175 x 31553015 x 26858.1m²300mm
Studio044175 x 21554015 x 16856.8m²300mm
Studio04 More4175 x 31554015 x 268510.8m²300mm

Ideally, we require a minimum of 50cm between the studio perimeter and any boundary or obstruction. The 50cm perimeter gap is to provide a workable space for the installers when they construct the studio. In some cases, it may be possible to reduce this gap slightly. Our installers will be able to advise how the gap could be reduced, dependent on site-specific factors. If it is possible to gain access to the other side of the boundary, by temporarily removing a fence panel for example, then we may be able to install the studio right next to the boundary. To discuss the specifics of your site, please contact us via email, along with some photos of the plot and rough dimensions.

In most cases, there’s no preparation needed before our installation team arrives in your garden, aside from ensuring the studio plot is cleared of any obstructions, such as garden furniture, potted plants etc.

If we are installing on lawn, you will not need to remove the top layer of turf.

The studio plot does not need to be perfectly level, as our foundations systems has some tolerance built in. Please get in touch if you would like to discuss the specifics of your garden.

There are broadly two types of foundations system we use, depending on the ground that your studio will be installed on.

If you plan to have your WOHOBO installed on lawn or bare ground, we use ground screws for the foundations. These look like giant screws and go into the ground to a depth of approximately 75cm to anchor the studio to the ground.

If you already have an existing solid base, such as a patio or concrete slab, or intend to install one, we use a system of adjustable risers that sit between the solid base and the base of the studio and these are bolted to create a strong bond.

We can also install our garden studios on a combination of a solid base and ground, as well as on gravel, so do get in touch if you would like to discuss any of these options.

Our garden studios arrive as large, flat prefabricated sections that are brought through to your garden and assembled in situ. This makes construction a quick process: we allow up to two consecutive days to construct our studios from start to finish.

Our garden studios are delivered as large flat prefabricated sections that are constructed on site in your garden. The largest section that cannot be dismantled in any way is the sliding door frame, which is delivered without the glass. Ideally, we need direct access into your garden, via a gate for example. If the only access is through your house, we will need a fairly straight route and you will need to measure all internal openings / doorways to check there is enough clearance (by measuring the height and width of the opening). If you would like us to check your measurements or access options, please get in touch and we’d be happy to help.

In most cases, you will not need planning permission to erect a WOHOBO, as they are classed as Permitted Development. If your property is not listed, or in a conservation area, AONB or national park, you should not need to get planning permission. The planning law stipulates that if a garden studio is positioned within 2m of the property’s boundary, its highest point must not exceed 2.5m. The highest point of a WOHOBO is 2.4m.

Building Regulations do not apply as the floor areas of all WOHOBO garden studios are less than 15 square metres and contain no sleeping accommodation. They also do not require an EPC (energy rating) due to be under 50 square metres.

WOHOBOs are fully insulated in the walls, roof and floor and are designed to be used all year round. We use a type of insulation called PIR (Polyisocyanurate), which has a high thermal performance. Compared with other types of mineral-based insulation, PIR is roughly half the thickness, making it an ideal choice for a garden studio where space can often be at a premium. From a sustainability point of view, PIR is one of the more environmentally friendly variants as less waste is produced during the manufacturing process and it can also be recycled.

In terms of heating WOHOBOs during the winter, we suggest just using a small plug-in electric heater. Given their compact size and the high-performance PIR insulation in the walls, roof and floor along with the double-glazed window, WOHOBOs heat up quickly and retain their heat well, making them efficient to run. You would not need to have the heater switched on the whole time you are in the studio on cold days. You may want to consider a WIFI-enabled heater, so that you can control the heating remotely.

Yes, it is possible to install air conditioning in a WOHOBO, especially if you are using your WOHOBO as a gym. A split system air conditioning unit would be the best option, and these come with heating options too. Please contact us if you would like more information about air conditioning.

The standard finish of the internal walls and ceiling is powder-coated steel in Alpine White. This finish is ready for you to move in and use, without needing to do any further work. If you want to change the look of the interior, it is possible for you to overclad the metal finish with wood panelling or plasterboard, for example. The steel walls can also be painted, as well as being magnetic, so you can use a range of magnets and magnetic fixings for hanging pictures, hooks and cladding. For screwing things into the walls, we recommend you use metal-to-metal self-tapping Tek screws.

The cedar side panels are for one or both sides of the studio, to provide a different aesthetic to the standard Slate Grey steel finish. The price per cedar side panel is £595 plus VAT for the Studio02/03/04. For the Studio 03 More/04 More the price per cedar side panel is £895 plus VAT.

Once you’re ready to order a WOHOBO, it’s a straightforward process. All the checks about your plot and access can be carried out over the phone or email, so please contact us in whichever way you wish. We will send you a quotation, to reflect the price as shown on the website, along with confirmation of the 5% deposit amount and ways to pay. Once we’ve received your deposit payment, your installation slot will be booked in and that’s pretty much it!

There is a 5-year warranty to cover faults in the galvanised steel frame, composite roof and wall panels, drainpipes, fascias, double-glazed units, and window frames. There is a 1-year warranty to cover faults in electrical fittings and window fixtures and fittings.

WOHOBOs are incredibly durable as they are essentially a metal structure, as opposed to wood.  

WOHOBOs are very easy to maintain. The galvanised steel frame and steel insulation panels look after themselves and will not rust. The external Western Red Cedar cladding is naturally hardy and can withstand all weather conditions. However, if left untreated over time, it will naturally change colour to a silvery grey. To retain the original colour of the cedar, it is recommended that the cedar is treated with a clear varnish once a year.

Included in the price of a WOHOBO is an electrics pack, which brings together the essential electrical fittings you’ll need. This includes internal and external lighting, power sockets, ethernet socket, a control pad, and all the necessary cabling. Our installers carry out first fix electrics, which means they put all the necessary cables inside the structure of the studio in all the right places. Your electrician will then need to wire in and certify the supplied electrical fittings inside the studio, and source and install a consumer unit for the studio. This has been designed to be a quick and straightforward job for an electrician to follow.

Your electrician will also need to arrange for an electrical supply to the studio. This is usually from your house, but can be from another external source, such as a garage.

We do not have a showroom; however, we can offer a virtual tour of one of our studios over video call. This can be a good opportunity to see things up close and ask lots of questions, but from the comfort of your own home. Please get in touch if you would like to arrange a virtual tour at a time to suit you.

The studio would need to be dismantled and rebuilt in sections, including new foundations, so it would need to be carried out by a builder or experienced tradesperson.

For that reason, it’s not a service we offer directly, but can talk things through with you if you’re considering it.

We focus on materials that are long-lasting, low maintenance and efficient.

  • steel structure and panels for durability
  • PIR insulation for strong thermal performance
  • double glazing to reduce heat loss
  • prefabrication to reduce waste on site
  • FSC cedar, used selectively where it performs best

The aim is a studio that performs well for years with minimal upkeep.

Before You Order

We offer six standard studio sizes. Dimensions below include external size, internal usable space, and the front porch.

All studios share the same height:

External height:
2430mm (highest point – rear)
2330mm (lowest point – front)

Internal ceiling height:
2180mm (highest point – rear)
2080mm (lowest point – front)

StudioExternal (mm)Internal (mm)Internal areaPorch
Studio022175 x 21552015 x 16853.4m²300mm
Studio02 More2175 x 31552015 x 26855.4m²300mm
Studio033175 x 21553015 x 16855.1m²300mm
Studio03 More3175 x 31553015 x 26858.1m²300mm
Studio044175 x 21554015 x 16856.8m²300mm
Studio04 More4175 x 31554015 x 268510.8m²300mm

WOHOBOs are built around a galvanised steel frame with insulated steel panels.

The insulation is closed-cell PIR, which provides strong thermal performance in a compact structure.

Externally, the studio features Western Red Cedar cladding on the front porch, with optional cedar side panels available.

The windows and doors are uPVC double-glazed units designed for durability and thermal efficiency.

Internally, the walls and ceiling are finished in powder-coated steel – clean, durable and ready to use straight away.

See Structure and materials for more detail.

Just give us a call or send us an email when you’re ready to go ahead and we’ll get the wheels in motion.

All checks around your plot, access and setup can be carried out remotely, so we’ll guide you through everything and send over a quotation.

Once the 5% deposit is received, your installation slot is booked and we’ll keep in touch along the way so you always know what’s happening next.

We don’t have a dedicated showroom.

There is a WOHOBO installed at a show home in Cheshire which can be visited. If that’s convenient, we can put you in touch to arrange a visit. If travelling isn’t practical, we can arrange a virtual tour with one of our team members.

Just get in touch and we’ll arrange a time that suits. We’ll walk you through a real WOHOBO over video so you can get a feel for the space, layout and materials, and talk through any questions you have.

We’re based in Derbyshire and install across mainland England, as well as parts of Wales and Scotland. If you’re unsure, just send us your postcode and we’ll confirm.

Delivery and installation are included within our standard pricing. Some areas outside of our usual delivery zone may incur an additional charge. If you send us your postcode, we can confirm this for you.

Optional cedar side panels are:

£595 + VAT (standard studios)

£895 + VAT (More versions)

No – side panels are optional and can be added to one or both sides.

They are best installed at the time of build. Retrofitting is possible, but a separate labour charge will apply.

We don’t supply heating or air conditioning as part of the package.

Most customers use a small plug-in heater in winter, which is usually more than enough due to the PIR insulation.

If you’d like more control, a small split-system air conditioning unit works very well and can be installed by a local specialist after installation.

See Structure and materials for more on how the studio performs.

In most cases, no. We can usually assess everything remotely using photos, measurements and a quick call if helpful.

If anything is unclear or unusual, we may recommend a site visit, but this isn’t normally required.

Installation & Setup

In most cases, very little. We just ask that the studio plot is cleared of any obstructions such as furniture or plants so the team has space to work.

If we are installing on lawn, there is no need to remove the turf.

The ground or base does not need to be perfectly level, as our foundation systems have some tolerance built in.

See Installation and foundations for more detail.

We install our studios using either:

  • ground screws (for soil or lawn)
  • adjustable risers (for solid bases like paving, concrete and gravel)

Both systems support the structure, allow precise levelling, and create airflow beneath the studio.

See Installation and foundations for full details.

Yes – ground screws are typically used for the foundations on lawn or soil.

The ground should be established, compacted, reasonably level and free from buried obstructions.

See Installation and foundations for more detail.

We need a clear route from the delivery vehicle to the garden.

Typical requirements:

  • around 2.2m height clearance
  • enough width for a two-person team to hand-carry long sections
  • minimal tight turns

If access is restricted, we can use a ‘deconstructed’ installation.

See Access and delivery for full details.

If there’s no side access to your garden, we can often bring the studio through the house.

In this case, the installation is carried out as a ‘deconstructed’ build, meaning the studio is delivered in smaller components to fit through standard sizes doorways and more of the assembly is carried out on site.

This works well in many homes, but it’s not always possible. We still need a fairly straight route through the property, and tight turns, narrow hallways or low ceilings can prevent access.

If you’re unsure, the best thing to do is send us a short video of the route from the roadside through to the garden. We can then talk through the options and provide component sizes if helpful.

See Access and delivery for more detail.

The installation team lays all cabling within the structure during installation.

Your electrician then:

  • installs the consumer unit
  • connects sockets and lighting
  • runs power from the house

See Electrics and internet for more details, or contact us to request the Electrics Guide.

Yes – each studio includes an ethernet socket.

The most reliable setup is to run a cable from your house router to the studio. Many customers then plug in a WiFi booster or mesh node inside.

See Electrics and internet for more detail.

Aftercare & Use

Yes – the PIR insulation in the walls, roof and floor provides effective thermal performance.

The studio warms up quickly and retains heat well. Most customers use a small plug-in heater intermittently to maintain a comfortable temperature.

Like any room with large glazing, the studio can warm up in direct sun.

The direction the front glazing faces is the biggest factor. External shading and ventilation usually keep things comfortable, and a small split-system air conditioning unit is a very effective option if you want more control.

See Structure and materials for more detail.

No – it is not soundproof.

The PIR insulation and double glazing reduce sound to a level suitable for normal use, but sound will travel in and out.

If needed, you can add acoustic treatment after installation.

There is a 5-year warranty covering the structure and materials, including the steel frame, panels, glazing and drainage.

There is also a 1-year warranty covering electrical fittings and window fixtures.

WOHOBOs are built around a steel structure, which makes them very durable.

The frame and panels require no routine maintenance.

The cedar cladding is naturally durable and can either be left to weather or treated annually if you prefer to maintain its colour.

The studio would need to be dismantled and rebuilt in sections, including new foundations, so it would need to be carried out by a builder or experienced tradesperson.

For that reason, it’s not a service we offer directly, but can talk things through with you if you’re considering it.

We focus on materials that are long-lasting, low maintenance and efficient.

  • steel structure and panels for durability
  • PIR insulation for strong thermal performance
  • double glazing to reduce heat loss
  • prefabrication to reduce waste on site
  • FSC cedar, used selectively where it performs best

The aim is a studio that performs well for years with minimal upkeep.